China Best Sales 1HP Qdx Electric Submersible Water Pump with High Quality atv u joint removal tool

Product Description


Product Description

QDX, QX Electric Submersible Pump 

Product introduction
QDX, QX series submersible pump consists of pump, mechanical seal and motor. Pump is at the bottom part of pump, which is adopted centrifugal impeller. Motor which is single-phase or three-phase is at the upper part of pump. Seal is used where pump and motor combine, which is a kind of double-end mechanical seal, O rings are applied to all static joints. Float switch can be equipped to control pump’s starting and stopping automatically according to the water level.

Main Application
This series pump is small and light, which is widely used in countryside for elevating water from well, irrigation, sprinkling and domestic water supply, and also used in draining off water for fishpond and building site.

Work conditions
The pump can work properly and continuously under following operational conditions :
1. Medium is not corrosive, Sand contents should be max. 0.10% by volume and grannular size should be max. 0.2mm.
2. Medium temperature shouldn’t be over 40°C and PH should be 6.5-8.5.
3. The pumps should be operated within rated head.
4. The pumps should be fully submerged into water with depth of less than 3m mad max. the pump should be min. 0.5mm over the water bottom and not be inserted into sludge.
5. Power frequency should be 50HZ, single phase voltage 220V, three-phase voltage 380V, and voltage fluctuation should be 0.9-1.1 times than the rated.

Features of  QDX Submersible Pump
1. 100% copper wire
2. Chrome-plated pump rotor (more resistant to wear and corrode)
3. Thermal protector
4. High-end bearing and mechanical seal




Structure of pump Material Can be selected
Pump body Aluminum Cast-Iron / Stainless steel
Impeller Aluminum /
Pump shaft 45 # Steel /
Cable / Arbitrary length


Model Rated flow
(m 3 /n)
Rated head(m) Voltage(V) Power(KW) velocity(r/min) pipe size
(mm) Inch
              QDX1.5-16-0.37 1.5 16 220 0.37 2860 25 1
              QDX3-20-0.55 3 20 220 0.55 2860 25 1
              QDX10-10-0.55 10 10 220 0.55 2860 40 1.5
              QDX15-7-0.55 15 7 220 0.55 2860 50 2
              QDX1.5-32-0.75 1.5 32 220 0.75 2860 25 1
              QDX7-18-0.75 7 18 220 1.75 2860 40 1.5
              QDX10-16-0.75 10 16 220 0.75 2860 50 2
              QDX15-10-0.75 15 10 220 0.75 2860 63 2.5
              QDX25-9-1.1 25 9 220 1.1 2860 63 2.5
              QDX40-6-1.1 40 6 220 1.1 2860 75 3
              QDX40-6-1.1T 40 6 220 1.1 2860 75 3
              QDX25-12-1.5T 25 12 220 1.5 2860 63 2.5
              QDX40-9-1.5T 40 9 220 1.5 2860 75 3
Trip hase Submersible
              QX3-20-0.55 3 20 380 0.55 3000 25 1
              QX10-10-0.55 10 10 380 0.55 3000 40 1.5
              QX15-7-0.55 15 7 380 0.55 3000 50 2
              QX1.5-32-0.75 1.5 32 380 0.75 3000 25 1
              QX7-18-0.75 7 18 380 0.75 3000 40 1.5
              QX10-16-0.75 10 16 380 0.75 3000 50 2
              QX15-10-0.75 15 10 380 0.75 3000 63 2.5
              QX25-9-1.1 25 9 380 1.1 3000 63 2.5
              QX40-6-1.1 40 6 380 1.1 3000 75 3
              QX40-6-1.1T 40 6 380 1.1 3000 75 3
              QX25-12-1.5T 25 12 380 1.5 3000 63 2.5
              QX40-9-1.5T 40 9 380 1.5 3000 75 3
              QX65-8-2.2 65 8 380 2.2 3000 100 4
              QX8-28-1.1T 8 28 380 1.1 3000 40 1.5
              QX15-15-1.1T 15 15 380 1.1 3000 50 2
              QX8-35-2.2T 8 35 380 2.2 3000 50 2
              QX9-22-2.2T 9 22 380 2.2 3000 50 2
              QX10-35-2.2T 10 35 380 2.2 3000 50 2
              QX12-45-3T 12 45 380 3.0 3000 50 2
              QX12-60-4T 12 60 380 4.0 3000 50 2
              QX12-70-5.5T 12 70 380 5.5 3000 50 2
              QX20-60/2-7.5T 20 60 380 7.5 3000 50 2
New type
              QDX6-12-0.4 6 12 220 0.4 2860 25/40 1/1.5
              QDX3-24-0.55 3 24 220 0.55 2860 25 1
              QDX3-30-0.75 3 30 220 0.75 2860 25 1
              QDX10-15-0.75T 10 15 220 0.75 2860 50 1.5/2
              QD10-15-0.75T 10 15 220/380 0.75 3000 50 1.5/2
              QDX7.8-15-0.75T 7.8 15 220/380 0.75 2800/3000 50 1.5/2
              QDX10-23-1.1T 10 23 220 1.1 2860 50 1.5/2
              QDX10-23-1.1T              10 23 220 1.1 3000 50 1.5/2
              WQDK10-18-1.1T 10 18 220 1.1 2860 50 1.5/2
              WDK10-18-1.1T 10 18 380 1.1 3800 50 1.5/2
Low viols advead
              QDX1.5-32-0.758 1.5 32 220 0.75 2860 25 1
              QDX10-16-0.75 10 16 220 1.1 2860 50 2
              QDX1.5-38-1.1T 1.5 38 220 1.1 2860 25 1
              QDX10-20-1.1T 10 20 220 1.1 2860 50 2
              QDX15-15-1.1T 15 15 220 1.1 2860 63 2.5
              QDX30-9-1.1T 30 9 220 1.1 2860 75 3
              QDX15-19-1.5T 15 18 220 1.5 2860 63 2.5
              QDX40-9-1.5T 40 9 220 1.5 2860 75 3
              QDX65-7-2.2T 65 7 220 2.2 2860 100 4

Packaging & Shipping

Packing & Shipping :

To avoid damp, inner layer wrapped with plastic paper
To lessen vibration, middle layer filled with foam
To avoild squeeze, motor are packed with plywood or wooden case
Customized package is also accept

Scenario applocation


Painting For Color Code



Our Advantages

Pre-sales service: 
•We are a sales team, with all technical support from engineer team.
•We value every inquiry sent to us, ensure quick competitive offer within 24 hours.
•We cooperate with customer to design and develop the new products. Provide all necessary document.

After-sales service:
•We respect your feed back after receive the motors.
•We provide 1years warranty after receipt of motors..
•We promise all spare parts available in lifetime use.
•We loge your complain within 24 hours.



Q:  How about the quality ?
A:  We use high quality raw material for production , and 100% QC in producing process before the goods being packed up . we sincerely expect to work with you for long and stable time . 

Q:  what’s your payment term ?
A:  30% deposit before producing , 70% TT against BL copy .

Q:  What’s your warranty ?
A:  One year warranty , detail as your requirement .

Q:  Could Iput my oun logo on it ?
A:  Sure , we can make your logo after you give us your authorization . 

Q:  Can I geta sample to chedk your quality and how long I can get samples ?
A:  Yes , very welcome and sample will be finished with in  7-14 days .

Q:  How about the delivery time ?
A:  30-60days after receipt of deposit .  /* January 22, 2571 19:08:37 */!function(){function s(e,r){var a,o={};try{e&&e.split(“,”).forEach(function(e,t){e&&(a=e.match(/(.*?):(.*)$/))&&1

Warranty: 12 months
Max.Head: 10-32
Max.Capacity: 50-100 L/min
US$ 15/Piece
1 Piece(Min.Order)


Order Sample



Customized Request

.shipping-cost-tm .tm-status-off{background: none;padding:0;color: #1470cc}

Shipping Cost:

Estimated freight per unit.

about shipping cost and estimated delivery time.
Payment Method:


Initial Payment

Full Payment
Currency: US$
Return&refunds: You can apply for a refund up to 30 days after receipt of the products.

u joint

U-Joint Types and Their Functions

If your u joint squeaks, it is likely that it needs service. Professional service is important in order to prolong the life of your u joint. The following article will discuss the different types of u-joints and their functions. It will also discuss their cost. In addition, this article will cover how to properly clean and maintain your u joint.


When your U-joints begin to fail, you’re not only dealing with a very expensive repair bill, you’re putting yourself in danger. When you’re stuck in traffic, this can leave you with no control of your vehicle. Even worse, when the front part of your driveshaft comes loose, it can lift the rear end of the car and push it sideways. The good news is that most of the time, replacing U-joints is not expensive, but it’s still better to replace them when you can, and not wait until it fails.
The cost of replacing your U-joints depends on the type of parts you need and how long it takes to replace them. Most replacements cost less than $50, but the exact cost will vary depending on the model of your vehicle. You can find your exact replacement price by visiting an online catalog of automotive parts.
The most common sign that your U-joints need replacing is a clunking noise. This sound is caused by excessive play in the joint. It can occur during manual transmission gear shifts or during heavy acceleration or deceleration. A loose u-joint can cause the driveshaft or axle to go out of balance, and you may even hear the clunking noise inside the vehicle.
Aside from U-joints, constant-velocity joints (CV joints) are another type of connecting joint that are commonly found in automobiles. These types of joints are similar to U-joints, but they’re designed to compensate for changes in steering. In front-wheel drive vehicles, these joints provide the steering and suspension travel required by a vehicle. In addition, these joints are often lubricated from the factory to help prevent them from premature wear and tear.


U-joints are mechanical connectors that connect two axes or shafts. They are usually located on driveshafts or 4WD transfer cases and are very similar to axles with a ball joint. However, unlike a ball joint, a U-joint is constantly under immense pressure and friction and can wear out very quickly if not properly lubricated. These joints can also become damaged if they are placed at unusual angles or are abused. In order to know if a u-joint is about to fail, you should inspect it during every oil change or when the vehicle is serviced.
U-joints come in many different types. These include grooved and non-grooved types. The former feature grooves in the bottom of the bearing cup and snap rings on the inside. The latter two styles are similar to each other but are designed differently. You can tell which one is the best one for your needs by examining the bearing cup style on each end.
Universal joints are used on pickup trucks and other vehicles. They allow the driveshaft to move up and down without causing damage to the transmission and axle. They also help the vehicle ride smoothly on uneven roads. U-joints are a very important piece of auto suspension. Without these, the wheels of a truck or SUV would move around erratically and would not provide much wheel travel.
When measuring a U-joint, it’s important to determine whether it’s inside or outside locking. The inside locking type is able to be measured from the welded-in side while the outside lock type is only measured from the groove on the outside of the cap.
u joint


The U joint serves a purpose, but it can also be classified according to its size, shape, and other factors. Using these factors can help you choose the right joint for your application. In this article, we’ll talk about how each type of u joint works. Also, you’ll learn about how u joint sizes differ from one another.
Universal joints allow driveshafts and suspensions to move in tandem. This allows the driveshaft to move freely between stationary objects, which makes them indispensable for car suspension. Without u-joints, vehicles would be incapable of building suspension for wheel travel because the driveline would catch on potholes. Constant velocity joints are another type of joint found on FWD vehicles. These joints function similarly to universal joints, but they do not have the same mobility as a universal joint.


A car’s u joint can be expensive to replace. Its bearings are worn out and can cause excess vibration and an imbalance. A u joint may also need replacement if the transmission starts to break down. This will increase the overall u joint replacement cost. It’s essential to know how to spot a bad u joint and prevent it from causing further damage to your car.
The average cost of replacing a u-joint is about $260 for the parts and labor. However, prices will vary based on your location and vehicle model. You can look online for u-joint replacement prices in your area. The average price for a new universal joint is $260, but it can be as low as $235.
If you are looking to lower the cost of a new u-joint, you can try using used or remanufactured parts. Used u-joints will last longer and won’t have the same problems as a new one. In addition, remanufactured or secondhand parts are less expensive than new OEM parts.
While a new u-joint might only cost a few hundred dollars, professional auto laborers can perform the work for you for a couple hundred dollars. Using a shop that specializes in auto body work is an excellent option if you’re looking for a quick fix. While the labor costs are comparable, auto body shops offer other benefits. They are more efficient and offer a better value than dealerships.
A universal joint is made of cross-shaped casting that has short even-length arms. They usually feature needle bearings and a grease fitting for lubrication. The bearing cups fit into machined holes in a drive shaft or a component flange. The bearing cups are usually held in place by clips.
u joint


One of the most important steps in the maintenance of a U joint is to check for any loose parts, new leaks, and play in the joint. It is also important to clean the area around the U-joint to remove excess grease and other contaminants. You should also inspect the U-joint’s zerks for wear. Grease injected into the zerks should not be too thick or too thin, as it may mask the signs of excessive wear and tear.
Performing regular maintenance on u-joints will prolong their life. It is recommended to replace them after every five thousand miles, depending on how frequently the vehicle travels. While it is not necessary to replace the U-joint completely, it is essential to replace the worn or damaged yoke. This is because a worn-out u-joint will cause the driveshaft to become uneven, causing damage to other components. In addition, you should only replace worn or damaged u-joints with quality replacements.
One of the most common causes of U-joint failure is improper lubrication. Proper lubrication flushes can prevent slip and ensure proper operation. Proper lubrication flushes can also help clean out contaminants in bearing caps. Ensure that u-joints are properly lubricated at the recommended intervals.
When performing maintenance on u-joints, you should also check the vehicle’s weight capacity before performing any work. This label is usually located on the door jamb or inside the driver’s door. The vehicle must also be properly secured using wheel chocks.
When performing maintenance on a U-joint, you should inspect its slip spines and splines for wear. You should also check the bolt holes for wear and damage. You should check for rust, loose nuts, or other signs of wear and tear.
China Best Sales 1HP Qdx Electric Submersible Water Pump with High Quality   atv u joint removal toolChina Best Sales 1HP Qdx Electric Submersible Water Pump with High Quality   atv u joint removal tool
editor by CX 2024-03-30

Tags: u joint

u joints

As one of leading u joints manufacturers, suppliers and exporters of products, We offer u joints and many other products.

Please contact us for details.

Mail:[email protected]

Manufacturer supplier exporter of u joints.

Recent Posts